XTool A80 Pro (H6 Pro) Program a Spare Key for 2015 Vauxhall Adam

Xtool Key Programmer

Here, xtool.co.uk runs through the process of programming a 2015 Vauxhall Adam using XTOOL A80 Pro (H6 Pro) diagnostic tool, where the customer required a spare key. Before doing so, uses the CGDI Godzilla Automatic Key Cutting Machine to cut the blade key firstly.

Step 1: Cut key blade by CGDI Godzilla

Step 2: Program new key by XTOOL A80 Pro

The specific operation procedure:

Step 1: Cut key blade by CGDI Godzilla  

1.Learn the original key

Turn on CGDI Godzilla key cutter

Go to the main menu

Select “Vehicle database”-> “Opel”-> “Astra”-> “HU100” which is the key profile of the new and of the old key

Xtool A80 Pro Program 2015 Vauxhall Adam 1 Xtool A80 Pro Program 2015 Vauxhall Adam 2

Note: There is not Adam model on the key cutter, but it got the same style of key as Astra, so select “Astra” model to do is fine.

On the top of the screen, it tells us which position the jaw needs to be in, so it says A, the t2 fixture A side and that’s how you align the key.

So go to put the original key in the jaw and align it up, and then hit “learning” on the screen

Xtool A80 Pro Program 2015 Vauxhall Adam 3

When it shows “successful key learning”, just hit “Ok”.

The bittings is got on the screen.

Xtool A80 Pro Program 2015 Vauxhall Adam 4

2.Cut new key

Next, go to load the new key.

Commence with the cut, load it and make sure it’s nice and flat.

There are no filings, and go to hit “Cutting”.

It gives us the cut in-depth and if there’s any offset that’s required. Use the default settings and press “Continue”.

Xtool A80 Pro Program 2015 Vauxhall Adam 5

It starts to cut the key.

Xtool A80 Pro Program 2015 Vauxhall Adam 6

When one side of the key is cut, remove the key from the jaw, clean off the filings. After that, put another side of the key to cut.

When both sides of the key are cut successfully, use a wire brush to clean it.

Xtool A80 Pro Program 2015 Vauxhall Adam 7

 

Step 2: Program new key by XTOOL A80 Pro

1.Read security code

Get the original key and the new key cut into the car.

The original key can start the car normally. There’s no warning light on the dashboard.

The new key turns fine, but it cannot start the car because it’s not programmed (there’s no central locking).

Now insert the original key into the ignition and turn on, connect the XTOOL VCI to the OBD port of the vehicle via the main cable, and connect to A80 Pro via Bluetooth

Xtool A80 Pro Program 2015 Vauxhall Adam 8

Note: It’s EU version which is a little different to the global version.

Select “Diagnosis”-> “Service”-> “Immobilization”

Xtool A80 Pro Program 2015 Vauxhall Adam 9

Agree with the disclaimer

Select “OPEL/VAUXHALL EU”-> “Read security code”-> “Type 4 (CAN GM- BCM)”-> “Read PIN Code”

Xtool A80 Pro Program 2015 Vauxhall Adam 10

Click “Yes” to read PIN when it asks “Type 4. Scan tool is going to read PIN, do you want to continue”.

You will hear the BCM clicking which means it’s communicating.

Read out the PIN code and got the VIN successfully

Xtool A80 Pro Program 2015 Vauxhall Adam 11

2.Program new key

Select “Immobiliser”-> “select from vehicle”-> “Adam”

Xtool A80 Pro Program 2015 Vauxhall Adam 12

  • Read number of key

Xtool A80 Pro Program 2015 Vauxhall Adam 13

  • Erase DTC

Xtool A80 Pro Program 2015 Vauxhall Adam 14

  • Program keys (without smart)

Select “Add keys”

Then follow the on-screen instructions to do as below:

-Close all doors and switch ignition on

-Input the security code and confirm it’s correct

Xtool A80 Pro Program 2015 Vauxhall Adam 15

-Open and close the driver door and confirm all electrical close

-Insert the key to be programmed and switch ignition on

-Switch ignition off, remove the key

-Open and close the driver door and confirm all electrical close again

-Switch ignition on… off… on

Now the key programming is completed, and then check if it can start the car or not.

Xtool A80 Pro Program 2015 Vauxhall Adam 16

Done!

Available link to get XTOOL A80 Pro with VCI+ diagnostic tool [UK/EU/US Ship No Tax]:

https://www.xtool.co.uk/wholesale/xtool-a80-pro-full-system-with-ecu-coding.html